HP 6002A Autoranging 0-50 VDC, 0-10 Amp

The HP 6002A dc power supply offers an exceptional combination of performance and flexibility.  It employes a unique control concept which provides for an autoranging output with the performance characteristics of linear regulation.  The HP 6002A is a 200 Watt CV/CC power supply, that provides Analog Programming of output voltages and current through the use of remotely controlled resistance or voltage applied to rear panel terminals.

Additional control terminals are provided for remote load voltage sensing, auto-series or parallel operation, and for remotely activating the crowbar circuit.  A pulse output from the crowbar terminal indicates the overvoltage circuit has been self-activated.  A voltage step change appearing on terminal indicates a changeover from constant-current operation.

Specifications

Input Voltage: 100, 120, 220, or 240 VAC, 48-63 Hz.

DC Output: voltage and current output can be adjusted over the ranges indicated by front panel controls, or analog

programming.

Voltage: 0-50 V

Current: 0-10 A

maximum 200 watts output from 20 V to 50 V.

Load Effect: constant-voltage, 0.01% +1 mV.  Constant current.

Source Effect: CV, 0.01% + 1 mV; CC, 0.01% + 1 mA.

PARD (ripple and noise): rms/p-p, 20 Hz to 20 MHz; CV, 1  mV/10 mV; CC, 5 mA rms.

Overvoltage protection: trip voltage adjustable from 2.5 V to 60 V.

DC output isolation: 150 VDC.

Size: approx. 7 x 8.5 x 16.5 inches.

Shipping Weight: 35 lbs.

1 available w/blue face

1 available w/grey face

Your Choice

$350.00 ea.   Warranty

stk#ES7529496023
stk#ES7529491933

HP 6002A/001 GPIB Autoranging 0-50 VDC, 0-10 Amp

The HP 6002A/001 (Option 001 provides HP-IB (IEEE-488) programmability) dc power supply offers an exceptional combination of performance and flexibility.  It employes a unique control concept which provides for an autoranging output with the performance characteristics of linear regulation.  The HP 6002A is a 200 Watt CV/CC power supply, that provides Analog Programming of output voltages and current through the use of remotely controlled resistance or voltage applied to rear panel terminals.

Additional control terminals are provided for remote load voltage sensing, auto-series or parallel operation, and for remotely activating the crowbar circuit.  A pulse output from the crowbar terminal indicates the overvoltage circuit has been self-activated.  A voltage step change appearing on terminal indicates a changeover from constant-current operation.<p>Digital programming via Option 001 permits control of output voltage or current by the HP-IB.  Two programmable ranges allow better resolution below 10 volts or 2 amps.  The selection of HP-IB control of either voltage or current is done by rear panel switches.  The IEEE 488 interface functions supported by the 6002A with Option 001 are basic listener (L2) and acceptor handshake (AH1).

Specifications

Input Voltage: 100, 120, 220, or 240 VAC, 48-63 Hz.

DC Output: voltage and current output can be adjusted over the ranges indicated by front panel controls, or analog programming.

Voltage: 0-50 V

Current: 0-10 A.

maximum 200 watts output from 20 V to 50 V. Load Effect: constant-voltage, 0.01% +1 mV.  Constant current.

Source Effect: CV, 0.01% + 1 mV; CC, 0.01% + 1 mA.

PARD (ripple and noise): rms/p-p, 20 Hz to 20 MHz; CV, 1  mV/10 mV; CC, 5 mA rms.

Overvoltage protection: trip voltage adjustable from 2.5 V to 60 V.

DC output isolation: 150 VDC.

Size: approx. 7 x 8.5 x 16.5 inches.

Shipping Weight: 35 lbs.

$400.00   Warranty

stk#ES7529493724

HP 6214C 10 W Laboratory Grade 0-10 VDC, 0-1 A CV/CC

HP Model 6214C bench supply is designed for general laboratory use and is equipped with front-panel mounted voltage and current controls, a combination volt/ammeter, and output binding posts.  Output voltage and curent are continuously variable, via coarse and fine conttrols from 0 to 15% above 10 VDC.  A switch selects either output voltage or curent for display on the panel meter.

Load connections are made via three binding posts.  Either the + or the - post may be grounded through an adjacent GND terminal or the supply may be operated floating at up to 300 volts above ground.

This supply can also be operated as a constant current  source with 500 µA load regulation.

Input power is 115 VAC ±10%, 48-440 Hz.

1 available.

$250.00   Warranty

HP 6216C 10 W Laboratory Grade 0-24 VDC, 0-0.4 A CV/CC

HP Model 6216C bench supply is designed for general laboratory use and is equipped with front-panel mounted voltage and current controls, a combination volt/ammeter, and output binding posts.  Output voltage and curent are continuously variable, via coarse and fine conttrols from 0 to 15% above 25 VDC.  A switch selects either output voltage or curent for display on the panel meter.

Load connections are made via three binding posts.  Either the + or the - post may be grounded through an adjacent GND terminal or the supply may be operated floating at up to 300 volts above ground.

This supply can also be operated as a constant current  source with 500 µA load regulation.

Input power is 115 VAC ±10%, 48-440 Hz.

$250.00   Warranty

 Back to Power Supply List